Accessories for 1-Wire

Loxone Accessories / Spare Parts

Loxone Replacement Plugs and Terminals

From €0.48

incl. VAT

plus shipping

From €14.32

incl. VAT

plus shipping


Accessories for Loxone 1-Wire

With the Loxone 1-Wire Extension you integrate low-cost temperature sensors and iButton keys into your smart home. Here you will find the matching sensors, keys and readers – and our adapter from our own production, with which you can also read 0–10 V sensors via 1-Wire.

What do I need for what? The overview

ItemUsed forSpecial featurePrice
1-Wire temperature sensorRoom temperature, e.g. in the switch box or distribution boardDS18B20, only 24 × 9 × 6 mm, with adhesive tape, single or set of 5ab €14.32
incl. VAT plus shipping
1-Wire sleeve temperature sensorOutdoor temperature, water, flow and return (also as a contact sensor)waterproof, −55 to 125 °C€17.55
incl. VAT plus shipping
iButtonElectronic key for access controlglobally unique 64-bit serial number€5.36
incl. VAT plus shipping
iButton magneticElectronic key for access controlmagnetic version€12.92
incl. VAT plus shipping
iButton Reader IndoorAccess indoorsred and green LEDs€13.99
incl. VAT plus shipping
iButton Reader OutdoorAccess outdoorsstainless steel€43.10
incl. VAT plus shipping
Adapter 2x 0–10 V to 1-WireReading 0–10 V sensors via 1-Wireown production, DIN rail 2 modules, detected as DS2438€60.87
incl. VAT plus shipping
Replacement connectors and terminalsReplacement for lost or damaged terminalssuitable for Loxone devicesab €0.48
incl. VAT plus shipping

How to plan your 1-Wire bus

Number of devices

You connect up to 20 sensors or one iButton reader to a 1-Wire Extension. The number of iButton keys, on the other hand, is unlimited. If you need several access points, use a separate Extension for each reader – otherwise the system does not know at which reader the key was presented.

Cable length and topology

If you lay the sensors in a line or as a bus with short stubs, up to 300 m is possible. With star topology or long stubs it is up to 100 m. If the sensors are parasitically powered (VDD to GND), the maximum is also 100 m, and the measuring range ends at +85 °C.

The right cable

A shielded CAT5, CAT6 or CAT7 cable is ideal: DQ and GND on one twisted pair, VDD on another core. Do not connect the shield, and no other data signals should run in the same cable.

Practical tips

A polling cycle of 60 seconds suits most applications; 300 seconds is enough for room temperature, while flow temperature control may need about 5 seconds. Seal the conduits in switch boxes – otherwise draughts will distort the readings.

Frequently asked questions

Do I need the 1-Wire Extension?

Yes. Sensors and iButton readers are connected to the 1-Wire Extension, which is connected to the Miniserver via Loxone Link.

How many sensors can I connect?

Loxone recommends up to 20 sensors per 1-Wire Extension. Up to 32 are possible, but then the demands on the wiring increase, and the cable length and polling cycle become shorter. An iButton reader, on the other hand, needs its own 1-Wire Extension.

How do I pair the sensors?

When searching in Loxone Config, the sensors are found with their serial number. So that you know which sensor is where, it is best to connect them one after another and pair them individually. Tip: if you briefly set the polling cycle to 1 second and touch a sensor, you can see from the change in value which one it is.

How does access with iButton work?

You hold the iButton to the reader, the 1-Wire Extension reads the unique serial number and your Loxone system checks the authorisation. You can also link functions, such as a welcome scene. The LEDs on the reader show red or green.

Can I read 0–10 V sensors via 1-Wire?

Yes, with our Adapter 2x 0–10 V to 1-Wire from our own production. It has two inputs, supplies the sensors with 24 V and is detected in Loxone as a DS2438.

Which sensor is suitable for outdoors or for pipes?

The waterproof sleeve temperature sensor measures from −55 to 125 °C and can also be used as a contact sensor on flow and return.

How quickly will my order arrive?

We usually ship items in stock on the day of the order (on Mondays for orders received by approx. 11 am, Tuesdays to Fridays by approx. 2 pm); delivery within Germany takes approx. 1–3 working days. If an item is not in stock in the quantity you want, we send the rest as quickly as possible and free of charge.

Your question was not answered?Write to us – we will be happy to help.

To the contact form