Accessories for Extensions

Loxone Accessories / Spare Parts

Loxone 120 Ohm Resistor

€0.30

incl. VAT

plus shipping

Accessories for Extensions

Loxone SMA Stub Antenna 868 MHz

€10.71

incl. VAT

plus shipping

Loxone Accessories / Spare Parts

Loxone SMA Antenna 868 MHz (Adhesive Antenna)

€22.93

incl. VAT

plus shipping

incl. VAT

plus shipping

Loxone Accessories / Spare Parts

Loxone Replacement Plugs and Terminals

From €0.48

incl. VAT

plus shipping

Loxone Accessories / Spare Parts

Replacement Relays for Loxone Products

From €4.58

incl. VAT

plus shipping

Cables / Wires / Wiring

Jumper Wire (Cut to Length and 100 m)

From €0.42

incl. VAT

plus shipping

incl. VAT

plus shipping


Accessories and spare parts for Loxone Extensions

Loxone Extensions add extra inputs and outputs, wireless and interfaces to your Miniserver in the distribution board. Here you will find everything you need for installing them: terminating resistors for the Link bus, antennas for the Air Base Extension, surge protection, replacement relays, terminals and connectors, and jumper wire for clean wiring.

What do I need for what?

ItemUsed forSpecial featurePrice
Loxone 120 Ohm ResistorBus termination for Link, Modbus and RS485original Loxone, clamps into the terminal€0.30
incl. VAT plus shipping
LOX-WID-120 bus terminating resistorBus termination on the DIN railfor Link and DMX bus, kit or ready-solderedab €9.79
incl. VAT plus shipping
LOX-WID-120 in 2-module housingBus termination on the DIN railfully assembled, housing with 2 modules€11.90
incl. VAT plus shipping
SMA rod antenna with tilt joint 868 MHzAntenna directly on the Extensionadjustable, 1.5 dBi€10.71
incl. VAT plus shipping
SMA adhesive antenna 868 MHzRouting the antenna out of the control cabinet3 m cable, self-adhesive€22.93
incl. VAT plus shipping
SMA rod antenna 4dBi 868 MHzAntenna outside the control cabinet4 dBi, with cable€31.93
incl. VAT plus shipping
LOXGUARD surge protectionProtection for 24 V, Link and TreeMade in Germanyab €37.89
incl. VAT plus shipping
Replacement relayReplacing a defective relayMiniserver, Relay Extension, Multi Extension Air, Smart Socket Airab €4.58
incl. VAT plus shipping
Retaining clip for Miniserver and ExtensionsHolding the device on the DIN railoriginal Loxone spare part€0.60
incl. VAT plus shipping
Replacement terminalsPush-in terminals for 2 × 4 conductorsin the colours for Link, Tree and 24 V
PCB connector 2-pole angledReplacement for plug-in terminals on Extensionsup to 12 A, orange, blue or green
Loxone replacement connectors and terminalsReplacement for connectors and terminalsalmost all Loxone connectorsab €0.48
incl. VAT plus shipping
Jumper WireWiring in the distribution boardtwisted, in Loxone colours, from 1 mab €0.42
incl. VAT plus shipping

Good to know

Terminating resistor at the end of the bus

Loxone Link needs a 120 ohm terminating resistor on the last device, just like a Modbus or RS485 bus. Without it, transmission errors can occur. You clamp the Loxone 120 Ohm Resistor directly into the terminal; the LOX-WID-120 sits as a separate module on the DIN rail.

Getting the wireless signal out of the distribution board

A metal distribution board weakens the wireless signal of the Air Base Extension or EnOcean Extension. With the adhesive antenna (3 m cable) or the rod antenna 4dBi you simply place the antenna outside.

Colours of the Loxone wiring

Loxone uses fixed colours: orange-white for 24 V, green-white for Tree and blue-white for Link. Our replacement terminals and the jumper wire are also available in these colours.

Frequently asked questions

Where does the terminating resistor go?

On the last device on the bus, between the two bus cores. With Loxone Link, that is the last Extension in the chain.

Which antenna is the right one?

You screw the rod antenna with tilt joint directly onto the SMA socket and align it. If the Extension is in a metal distribution board, use the adhesive antenna with 3 m cable or the rod antenna 4dBi with cable and mount it outside.

Which replacement relay fits my device?

For the replacement relay, select the device via the variant: Miniserver V1 with Extension, Miniserver V2, Relay Extension, Multi Extension Air or Smart Socket Air.

What do I need the LOXGUARD for?

The LOXGUARD protects your Loxone components against surges on the 24 V, Link and Tree lines. Choose the model according to which lines you want to protect.

How quickly will my order arrive?

We usually ship items in stock on the day of the order (on Mondays for orders received by approx. 11 am, Tuesdays to Fridays by approx. 2 pm); delivery within Germany takes approx. 1–3 working days. If an item is not in stock in the quantity you want, we send the rest as quickly as possible and free of charge.

Your question was not answered?Write to us – we will be happy to help.

To the contact form